ARDE Barinco Inc.
Carlstadt, NJ
201-784-9880 or 800-909-6070
Fax: 201-784-0483
abmix@ardeinc.com
www.abmixer.com
MXM50-AP Maximixer
Attributes/comments: A multi-shaft mixing system combining scrapped surface agitation with a reversible high shear homogenizing mixer. The 50 liter vessel is fully jacketed for heating and cooling with insulation and a sanitary stainless steel sheath. Both mixers can be automatically lifted out of the mixing vessel to allow movement of the vessel away from the mixing station. A heating, cooling and air pressure system was supplied along with temperature measurement in a complete control panel.
CB Mills
Gurnee, IL
847-662-4000
Fax: 847-662-4003
sales@cbmills.com
www.cbmills.com
DYNO-Mill, ECM-AP
Attributes/comments: New separation system of the DYNO-Mill ECM-AP. New design of the grinding chamber allows higher throughput and production capacities, especially for highly viscous products. Increased wear resistance of contract parts. Ability to use beads with a size of 0.1 mm.
Charles Ross & Son Company
Hauppauge, NY
631-234-0500
Fax: 631-234-0691
sales@mixers.com
www.mixers.com
Model HSM-100CI-T Laboratory Mixer
Attributes/comments: The HSM-100LCI-T is a new multi-purpose laboratory mixer. Offered with interchangeable mixing attachments including batch and inline rotor/stator sets, disperser blades and propellers, this bench-top machine is ideal for powder wet-wout and dispersion, deagglomeration, particle size reduction, solubilization, emulsification and homogenization. Features include: Type 316 stainless steel wetted parts polished to 150-grit finish, 1 HP drive, 115 volt, 50/60 Hz, single phase, 20 amp motor (optional voltage available), variable speed controls and display for speed, percent of load, batch timer and temperature, electronic push-button lift, dust and fluid spray-resistant enclosure, easy to dissemble and clean with simple hand tools, temperatures probe, vessel/beaker clamp assembly, vacuum cover and mix vessel, data acquisition/PC control and other features are available as options.
Conn and Company
Warren, PA
814-723-7980
Fax: 814-723-8502
rcfreeman@connblade.com
www.connblade.com
Conn Blade now available in UHMW Polyethylene
Attributes/comments: Most efficient and aggressive Poly Blade available. Provides combination of pumping action for material turnover and shear/dispersion. Low shear without teeth also available. Gives much longer life than typical metal blades. When leading edges are worn blade can be be turned over to start like new. Also available in polyurethane, nylon, Teflon, polypropylene and other materials. Traditional stainless Conn Blades readily available.
EMI - Engineered Mills, Inc.
Grayslake, IL
847-548-0044
Fax: 847-548-0099
sales@EMImills.com
www.EMImills.com
EMI Laboratory
Mixer/Disperser/Rotor Stator
Attributes/comments: EMI manufactures heavy duty lab/pilot mixers to meet explosion proof and standard requirements. The mixer/disperser can be converted to a rotor/stator head and batch bead mill making them adaptable to the project requirements. Available with 0.5 to 3 HP AC motors that are quiet, energy efficient and variable speed with high torque.
Glen Mills Inc.
Clifton, NJ
973-777-0777
Fax: 973-777-0070
staff@glenmills.com
www.glenmills.com
Jar Mills Using Ceramic Jars
Attributes/comments: The new innovation of using high strength and chemically resistant jars allows the old tried-and-true Jar Mill to now handle more exotic materials. Jars made of ZrO/yttria composition offer low wear for long life and less contamination of milled products. The ceramic’s low porosity makes cleaning between runs easier. Glen Mills’ Jar Mills can handle a variety of jar sizes, and the mills can be single-tier or multi-tiered for more productivity in a confined space. Pictured are ceramic jars with metal strengthening sections.
Ceramic Grinding Media for Jar Mills and Media Mills
Attributes/comments: Advanced ceramics, such as zirconium oxide stabilized with yttria have application in the comminution of solids where contamination is a concern. Glen Mills offer grinding media in ball and rod shapes from 30 microns up to 25mm. The low wear of these parts allows for long mill and media life and minimal contamination of the milled products. The low porosity of the ceramics expedites cleaning and essentially eliminates cross contamination between batches.
Hero Products Group
Delta, British Columbia
604-523-2460
Fax: 604-522-8735
ayong@hero.ca
www.hero.ca
TruMix5 XHD
Attributes/comments: This extra heavy duty model provides specialized mixing motion for 5-gallons of those heavy materials, such as stucco or block filler. Its tough build effortlessly accommodates up to 80 lbs., contains life-time sealed bearings, and operates maintenance free.
TruMix Ergo 5
Attributes/comments: This vortex 5-gallon paint mixer is the first of its kind with an enhanced ergonomic design that minimizes operator strain, typically associated with the loading and unloading of heavy 5-gallon pails. The Ergo5 will be available in market the second quarter of 2013.
Jaygo,Inc.
Union, NJ 07083
908-688-3600
Fax: 908-688-6060
www.jaygoinc.com
FAMAT Sampling Valves
Attributes/comments: Jaygo, Inc. is introducing the new FAMAT Sampling Valves.
The sampling valves are based on the patented E.P. EXPANDING PISTON Technology. The patented system inside this piston allows the PTFE external layer to expand and insure a perfect seal.
Samples can be taken under process conditions:
- From vacuum up to 145 psi (10 bar)
- Temperature between -4°F (-20°C) and 360°F (180°C). (On request up to 570°F (300°C)).
The advantage of having an expendable piston inside the valve is to eliminate the need for O-rings that can be damaged during valve operation, and consequently generate a contamination point. Another big advantage of the design is that in closed position, the piston will be flush with the connection point, leaving no dead space
Morehouse Cowles
Chino, GA
800-625-4819
Fax: 909-627-7366
rockyc@morehousecowles.com
www.morehousecowles.com
Variable Speed Dissolvers
Attributes/comments: Morehouse Cowles in-stock selection of genuine models from 1 to 250 HP are the standard of the industry. They are equipped with mechanical variable or invester variable speed and a hydraulic lift for multiple tank operation.
Zinger Horizontal Media Mill
Attributes/comments: The unique, patented rotor and chamber design aggressively accelerates media through the slurry and has proven to reduce particle size in significantly less time than the conventional disc mill design.
Netzsch Premier Technologies, LLC
Exton, PA
800-676-6455/484-879-2020
Fax: 610-280-1299
info.npt@netzsch.com
www.netzsch-grinding.com/coatings
Netzsch Omega Economic Dispersionizer
Attributes/comments: The Omega Economic Dispersionizer offering efficient dispersion of particles, creating small particle sizes using significantly reduced heat generation while the dispersion process offers a higher degree of efficiency and shorter processing time.
The Netzsch Condux CGS-10
Attributes/comments: The Netzsch Condux CGS-10 for contamination free dry grinding of material of any hardness. Now available in Netzsch’s Exton, PA lab.
Red Devil Equipment Company
Plymouth, MN
763-533-2969
Fax: 763-533-0015
info@reddevilequipment.com
www.reddevilequipment.com
Air Devil Pneumatic Shaker
Attributes/comments: By incorporating a heavy duty air cylinder and sealed ball bearings, this pneumatic shaker is designed to eliminate the friction and wear commonly associated with competing models. It requires airflow of 70-135 PSI and shakes containers up to 11” in height.
Model 5000 Plwwatform Shaker
Attributes/comments: Designed for medium traffic retail outlets, it is ideal for mixing all types of architectural paints and primers. It accepts pints to five-gallon containers, including cans, and features
Carlstadt, NJ
201-784-9880 or 800-909-6070
Fax: 201-784-0483
abmix@ardeinc.com
www.abmixer.com
MXM50-AP Maximixer
Attributes/comments: A multi-shaft mixing system combining scrapped surface agitation with a reversible high shear homogenizing mixer. The 50 liter vessel is fully jacketed for heating and cooling with insulation and a sanitary stainless steel sheath. Both mixers can be automatically lifted out of the mixing vessel to allow movement of the vessel away from the mixing station. A heating, cooling and air pressure system was supplied along with temperature measurement in a complete control panel.
CB Mills
Gurnee, IL
847-662-4000
Fax: 847-662-4003
sales@cbmills.com
www.cbmills.com
DYNO-Mill, ECM-AP
Attributes/comments: New separation system of the DYNO-Mill ECM-AP. New design of the grinding chamber allows higher throughput and production capacities, especially for highly viscous products. Increased wear resistance of contract parts. Ability to use beads with a size of 0.1 mm.
Charles Ross & Son Company
Hauppauge, NY
631-234-0500
Fax: 631-234-0691
sales@mixers.com
www.mixers.com
Model HSM-100CI-T Laboratory Mixer
Attributes/comments: The HSM-100LCI-T is a new multi-purpose laboratory mixer. Offered with interchangeable mixing attachments including batch and inline rotor/stator sets, disperser blades and propellers, this bench-top machine is ideal for powder wet-wout and dispersion, deagglomeration, particle size reduction, solubilization, emulsification and homogenization. Features include: Type 316 stainless steel wetted parts polished to 150-grit finish, 1 HP drive, 115 volt, 50/60 Hz, single phase, 20 amp motor (optional voltage available), variable speed controls and display for speed, percent of load, batch timer and temperature, electronic push-button lift, dust and fluid spray-resistant enclosure, easy to dissemble and clean with simple hand tools, temperatures probe, vessel/beaker clamp assembly, vacuum cover and mix vessel, data acquisition/PC control and other features are available as options.
Conn and Company
Warren, PA
814-723-7980
Fax: 814-723-8502
rcfreeman@connblade.com
www.connblade.com
Conn Blade now available in UHMW Polyethylene
Attributes/comments: Most efficient and aggressive Poly Blade available. Provides combination of pumping action for material turnover and shear/dispersion. Low shear without teeth also available. Gives much longer life than typical metal blades. When leading edges are worn blade can be be turned over to start like new. Also available in polyurethane, nylon, Teflon, polypropylene and other materials. Traditional stainless Conn Blades readily available.
EMI - Engineered Mills, Inc.
Grayslake, IL
847-548-0044
Fax: 847-548-0099
sales@EMImills.com
www.EMImills.com
EMI Laboratory
Mixer/Disperser/Rotor Stator
Attributes/comments: EMI manufactures heavy duty lab/pilot mixers to meet explosion proof and standard requirements. The mixer/disperser can be converted to a rotor/stator head and batch bead mill making them adaptable to the project requirements. Available with 0.5 to 3 HP AC motors that are quiet, energy efficient and variable speed with high torque.
Glen Mills Inc.
Clifton, NJ
973-777-0777
Fax: 973-777-0070
staff@glenmills.com
www.glenmills.com
Jar Mills Using Ceramic Jars
Attributes/comments: The new innovation of using high strength and chemically resistant jars allows the old tried-and-true Jar Mill to now handle more exotic materials. Jars made of ZrO/yttria composition offer low wear for long life and less contamination of milled products. The ceramic’s low porosity makes cleaning between runs easier. Glen Mills’ Jar Mills can handle a variety of jar sizes, and the mills can be single-tier or multi-tiered for more productivity in a confined space. Pictured are ceramic jars with metal strengthening sections.
Ceramic Grinding Media for Jar Mills and Media Mills
Attributes/comments: Advanced ceramics, such as zirconium oxide stabilized with yttria have application in the comminution of solids where contamination is a concern. Glen Mills offer grinding media in ball and rod shapes from 30 microns up to 25mm. The low wear of these parts allows for long mill and media life and minimal contamination of the milled products. The low porosity of the ceramics expedites cleaning and essentially eliminates cross contamination between batches.
Hero Products Group
Delta, British Columbia
604-523-2460
Fax: 604-522-8735
ayong@hero.ca
www.hero.ca
TruMix5 XHD
Attributes/comments: This extra heavy duty model provides specialized mixing motion for 5-gallons of those heavy materials, such as stucco or block filler. Its tough build effortlessly accommodates up to 80 lbs., contains life-time sealed bearings, and operates maintenance free.
TruMix Ergo 5
Attributes/comments: This vortex 5-gallon paint mixer is the first of its kind with an enhanced ergonomic design that minimizes operator strain, typically associated with the loading and unloading of heavy 5-gallon pails. The Ergo5 will be available in market the second quarter of 2013.
Jaygo,Inc.
Union, NJ 07083
908-688-3600
Fax: 908-688-6060
www.jaygoinc.com
FAMAT Sampling Valves
Attributes/comments: Jaygo, Inc. is introducing the new FAMAT Sampling Valves.
The sampling valves are based on the patented E.P. EXPANDING PISTON Technology. The patented system inside this piston allows the PTFE external layer to expand and insure a perfect seal.
Samples can be taken under process conditions:
- From vacuum up to 145 psi (10 bar)
- Temperature between -4°F (-20°C) and 360°F (180°C). (On request up to 570°F (300°C)).
The advantage of having an expendable piston inside the valve is to eliminate the need for O-rings that can be damaged during valve operation, and consequently generate a contamination point. Another big advantage of the design is that in closed position, the piston will be flush with the connection point, leaving no dead space
Morehouse Cowles
Chino, GA
800-625-4819
Fax: 909-627-7366
rockyc@morehousecowles.com
www.morehousecowles.com
Variable Speed Dissolvers
Attributes/comments: Morehouse Cowles in-stock selection of genuine models from 1 to 250 HP are the standard of the industry. They are equipped with mechanical variable or invester variable speed and a hydraulic lift for multiple tank operation.
Zinger Horizontal Media Mill
Attributes/comments: The unique, patented rotor and chamber design aggressively accelerates media through the slurry and has proven to reduce particle size in significantly less time than the conventional disc mill design.
Netzsch Premier Technologies, LLC
Exton, PA
800-676-6455/484-879-2020
Fax: 610-280-1299
info.npt@netzsch.com
www.netzsch-grinding.com/coatings
Netzsch Omega Economic Dispersionizer
Attributes/comments: The Omega Economic Dispersionizer offering efficient dispersion of particles, creating small particle sizes using significantly reduced heat generation while the dispersion process offers a higher degree of efficiency and shorter processing time.
The Netzsch Condux CGS-10
Attributes/comments: The Netzsch Condux CGS-10 for contamination free dry grinding of material of any hardness. Now available in Netzsch’s Exton, PA lab.
Red Devil Equipment Company
Plymouth, MN
763-533-2969
Fax: 763-533-0015
info@reddevilequipment.com
www.reddevilequipment.com
Air Devil Pneumatic Shaker
Attributes/comments: By incorporating a heavy duty air cylinder and sealed ball bearings, this pneumatic shaker is designed to eliminate the friction and wear commonly associated with competing models. It requires airflow of 70-135 PSI and shakes containers up to 11” in height.
Model 5000 Plwwatform Shaker
Attributes/comments: Designed for medium traffic retail outlets, it is ideal for mixing all types of architectural paints and primers. It accepts pints to five-gallon containers, including cans, and features
